TELNET(1C) TELNET(1C) NAME telnet - user interface to the TELNET protocol SYNOPSIS telnet [ host [ port ] ] DESCRIPTION _T_e_l_n_e_t is used to communicate with another host using the TELNET proto‐ col. If _t_e_l_n_e_t is invoked without arguments, it enters command mode, indicated by its prompt (“telnet>”). In this mode, it accepts and exe‐ cutes the commands listed below. If it is invoked with arguments, it performs an open command (see below) with those arguments. Once a connection has been opened, _t_e_l_n_e_t enters an input mode. The input mode entered will be either “character at a time” or “line by line” depending on what the remote system supports. In “character at a time” mode, most text typed is immediately sent to the remote host for processing. In “line by line” mode, all text is echoed locally, and (normally) only completed lines are sent to the remote host. The “local echo charac‐ ter” (initially “^E”) may be used to turn off and on the local echo (this would mostly be used to enter passwords without the password being echoed). In either mode, if the _l_o_c_a_l_c_h_a_r_s toggle is TRUE (the default in line mode; see below), the user’s _q_u_i_t, _i_n_t_r, and _f_l_u_s_h characters are trapped locally, and sent as TELNET protocol sequences to the remote side. There are options (see toggle _a_u_t_o_f_l_u_s_h and toggle _a_u_t_o_s_y_n_c_h below) which cause this action to flush subsequent output to the termi‐ nal (until the remote host acknowledges the TELNET sequence) and flush previous terminal input (in the case of _q_u_i_t and _i_n_t_r). While connected to a remote host, _t_e_l_n_e_t command mode may be entered by typing the _t_e_l_n_e_t “escape character” (initially “^]”). When in command mode, the normal terminal editing conventions are available. COMMANDS The following commands are available. Only enough of each command to uniquely identify it need be typed (this is also true for arguments to the mode, set, toggle, and display commands). open _h_o_s_t [ _p_o_r_t ] Open a connection to the named host. If no port number is spec‐ ified, _t_e_l_n_e_t will attempt to contact a TELNET server at the default port. The host specification may be either a host name (see _h_o_s_t_s(5)) or an Internet address specified in the “dot notation” (see _i_n_e_t(3N)). close Close a TELNET session and return to command mode. quit Close any open TELNET session and exit _t_e_l_n_e_t. An end of file (in command mode) will also close a session and exit. z Suspend _t_e_l_n_e_t. This command only works when the user is using the _c_s_h(1). mode _t_y_p_e _T_y_p_e is either _l_i_n_e (for “line by line” mode) or _c_h_a_r_a_c_t_e_r (for “character at a time” mode). The remote host is asked for per‐ mission to go into the requested mode. If the remote host is capable of entering that mode, the requested mode will be entered. status Show the current status of _t_e_l_n_e_t. This includes the peer one is connected to, as well as the current mode. display [ _a_r_g_u_m_e_n_t_._._. ] Displays all, or some, of the set and toggle values (see below). ? [ _c_o_m_m_a_n_d ] Get help. With no arguments, _t_e_l_n_e_t prints a help summary. If a command is specified, _t_e_l_n_e_t will print the help information for just that command. send _a_r_g_u_m_e_n_t_s Sends one or more special character sequences to the remote host. The following are the arguments which may be specified (more than one argument may be specified at a time): _e_s_c_a_p_e Sends the current _t_e_l_n_e_t escape character (initially “^]”). _s_y_n_c_h Sends the TELNET SYNCH sequence. This sequence causes the remote system to discard all previously typed (but not yet read) input. This sequence is sent as TCP urgent data (and may not work if the remote system is a 4.2 BSD system -- if it doesn’t work, a lower case “r” may be echoed on the terminal). _b_r_k Sends the TELNET BRK (Break) sequence, which may have significance to the remote system. _i_p Sends the TELNET IP (Interrupt Process) sequence, which should cause the remote system to abort the currently running process. _a_o Sends the TELNET AO (Abort Output) sequence, which should cause the remote system to flush all output from the remote system to the user’s terminal. _a_y_t Sends the TELNET AYT (Are You There) sequence, to which the remote system may or may not choose to respond. _e_c Sends the TELNET EC (Erase Character) sequence, which should cause the remote system to erase the last charac‐ ter entered. _e_l Sends the TELNET EL (Erase Line) sequence, which should cause the remote system to erase the line currently being entered. _g_a Sends the TELNET GA (Go Ahead) sequence, which likely has no significance to the remote system. _n_o_p Sends the TELNET NOP (No OPeration) sequence. _? Prints out help information for the send command. set _a_r_g_u_m_e_n_t _v_a_l_u_e Set any one of a number of _t_e_l_n_e_t variables to a specific value. The special value “off” turns off the function associated with the variable. The values of variables may be interrogated with the display command. The variables which may be specified are: _e_c_h_o This is the value (initially “^E”) which, when in “line by line” mode, toggles between doing local echoing of entered characters (for normal processing), and suppress‐ ing echoing of entered characters (for entering, say, a password). _e_s_c_a_p_e This is the _t_e_l_n_e_t escape character (initially “^[”) which causes entry into _t_e_l_n_e_t command mode (when con‐ nected to a remote system). _i_n_t_e_r_r_u_p_t If _t_e_l_n_e_t is in _l_o_c_a_l_c_h_a_r_s mode (see toggle _l_o_c_a_l_c_h_a_r_s below) and the _i_n_t_e_r_r_u_p_t character is typed, a TELNET IP sequence (see send _i_p above) is sent to the remote host. The initial value for the interrupt character is taken to be the terminal’s intr character. _q_u_i_t If _t_e_l_n_e_t is in _l_o_c_a_l_c_h_a_r_s mode (see toggle _l_o_c_a_l_c_h_a_r_s below) and the _q_u_i_t character is typed, a TELNET BRK sequence (see send _b_r_k above) is sent to the remote host. The initial value for the quit character is taken to be the terminal’s quit character. _f_l_u_s_h_o_u_t_p_u_t If _t_e_l_n_e_t is in _l_o_c_a_l_c_h_a_r_s mode (see toggle _l_o_c_a_l_c_h_a_r_s below) and the _f_l_u_s_h_o_u_t_p_u_t character is typed, a TELNET AO sequence (see send _a_o above) is sent to the remote host. The initial value for the flush character is taken to be the terminal’s flush character. _e_r_a_s_e If _t_e_l_n_e_t is in _l_o_c_a_l_c_h_a_r_s mode (see toggle _l_o_c_a_l_c_h_a_r_s below), and if _t_e_l_n_e_t is operating in “character at a time” mode, then when this character is typed, a TELNET EC sequence (see send _e_c above) is sent to the remote system. The initial value for the erase character is taken to be the terminal’s erase character. _k_i_l_l If _t_e_l_n_e_t is in _l_o_c_a_l_c_h_a_r_s mode (see toggle _l_o_c_a_l_c_h_a_r_s below), and if _t_e_l_n_e_t is operating in “character at a time” mode, then when this character is typed, a TELNET EL sequence (see send _e_l above) is sent to the remote system. The initial value for the kill character is taken to be the terminal’s kill character. _e_o_f If _t_e_l_n_e_t is operating in “line by line” mode, entering this character as the first character on a line will cause this character to be sent to the remote system. The initial value of the eof character is taken to be the terminal’s eof character. toggle _a_r_g_u_m_e_n_t_s_._._. Toggle (between TRUE and FALSE) various flags that control how _t_e_l_n_e_t responds to events. More than one argument may be speci‐ fied. The state of these flags may be interrogated with the display command. Valid arguments are: _l_o_c_a_l_c_h_a_r_s If this is TRUE, then the _f_l_u_s_h, _i_n_t_e_r_r_u_p_t, _q_u_i_t, _e_r_a_s_e, and _k_i_l_l characters (see set above) are recognized locally, and transformed into (hopefully) appropriate TELNET control sequences (respectively _a_o, _i_p, _b_r_k, _e_c, and _e_l; see send above). The initial value for this tog‐ gle is TRUE in “line by line” mode, and FALSE in “charac‐ ter at a time” mode. _a_u_t_o_f_l_u_s_h If _a_u_t_o_f_l_u_s_h and _l_o_c_a_l_c_h_a_r_s are both TRUE, then when the _a_o, _i_n_t_r, or _q_u_i_t characters are recognized (and trans‐ formed into TELNET sequences; see set above for details), _t_e_l_n_e_t refuses to display any data on the user’s terminal until the remote system acknowledges (via a TELNET _T_i_m_i_n_g _M_a_r_k option) that it has processed those TELNET sequences. The initial value for this toggle is TRUE if the terminal user had not done an "stty noflsh", other‐ wise FALSE (see _s_t_t_y_(_1_)_)_. _a_u_t_o_s_y_n_c_h If _a_u_t_o_s_y_n_c_h and _l_o_c_a_l_c_h_a_r_s are both TRUE, then when either the _i_n_t_r or _q_u_i_t characters is typed (see set above for descriptions of the _i_n_t_r and _q_u_i_t characters), the resulting TELNET sequence sent is followed by the TELNET SYNCH sequence. This procedure should cause the remote system to begin throwing away all previously typed input until both of the TELNET sequences have been read and acted upon. The initial value of this toggle is FALSE. _c_r_m_o_d Toggle carriage return mode. When this mode is enabled, most carriage return characters received from the remote host will be mapped into a carriage return followed by a line feed. This mode does not affect those characters typed by the user, only those received from the remote host. This mode is not very useful unless the remote host only sends carriage return, but never line feed. The initial value for this toggle is FALSE. _d_e_b_u_g Toggles socket level debugging (useful only to the _s_u_p_e_‐ _ruser_)_. The initial value for this toggle is FALSE. _o_p_t_i_o_n_s Toggles the display of some internal _t_e_l_n_e_t protocol pro‐ cessing (having to do with TELNET options). The initial value for this toggle is FALSE. _n_e_t_d_a_t_a Toggles the display of all network data (in hexadecimal format). The initial value for this toggle is FALSE. _? Displays the legal toggle commands. BUGS There is no adequate way for dealing with flow control. On some remote systems, echo has to be turned off manually when in “line by line” mode. There is enough settable state to justify a ._t_e_l_n_e_t_r_c file. No capability for a ._t_e_l_n_e_t_r_c file is provided. In “line by line” mode, the terminal’s _e_o_f character is only recognized (and sent to the remote system) when it is the first character on a line. 4.2 Berkeley Distribution May 10, 1986 TELNET(1C)