XP(4)		    UNIX Programmer's Manual		    XP(4)


NAME
     xp - generic SMD moving-head disk

SYNOPSIS
     /sys/conf/SYSTEM:
	  NXPC	  xp_controllers # Number of controllers
	  NXPD	  xp_drives	 # RM02/03/05, RP04/05/06,
				 # CDC 9766, Fuji 160, etc.
	  BADSECT NO		 # Bad sector handling (see BUGS)

     /etc/dtab:
	  #Name Unit# Addr   Vector Br Handler(s)      # Comments
	  xp	?     176700 254    5  xpintr	       # xp driver

     major device number(s):
	  raw: 19
	  block: 10
     minor device encoding:
	  bits 0007 specify partition of XP drive
	  bits 0370 specify XP drive

DESCRIPTION
     The xp driver is a generic SMD storage module disk driver.
     It can be adapted to most SMD controllers although
     bootstrapping will not necessarily be directly possible.
     The drives are numbered from 0 to n on controller 0, from
     n+1 to m on controller 1, etc.  The drives may have dif-
     ferent geometries.

     The xp driver is unique amoungst 2BSD drivers in its number-
     ing of drives.  Other drivers (ra for example) number drives
     0 thru 7 on controller 1, 8 thru 15 on controller 2 and so
     on.  xp on the other hand can have drives 0 and 1 on con-
     troller 1, drives 2, 3, 4 and 5 on controller 2 and drives
     6, 7 and 8 on controller 3.  This is different from boot's
     view of the world, so if you are booting from other than
     unit 0 you may have to experiment a bit.

     Files with minor device numbers 0 through 7 refer to various
     portions of drive 0; minor devices 8 through 15 refer to
     drive 1, etc.  The standard device names begin with ``xp''
     followed by the drive number and then a letter a-h for par-
     titions 0-7 respectively.	The character ? stands here for a
     drive number in the range 0-7.

     The block files access the disk via the system's normal
     buffering mechanism and may be read and written without
     regard to physical disk records.  There is also a `raw'
     interface which provides for direct transmission between the
     disk and the user's read or write buffer.	A single read or
     write call results in exactly one I/O operation and there-
     fore raw I/O is considerably more efficient when many words


Printed 11/26/99	 August 14, 1995			1


XP(4)		    UNIX Programmer's Manual		    XP(4)


     are transmitted.  The names of the raw files conventionally
     begin with an extra `r.'

     In raw I/O the buffer must begin on a word (even) boundary,
     and counts should be a multiple of 512 bytes (a disk sec-
     tor).  Likewise lseek calls should specify a multiple of 512
     bytes.

DISK SUPPORT
     Disks must be labeled using either the standalone disklabel
     program on the boot tape or with the disklabel(8) program.
     The kernel no longer attempts to determine the drive type
     and geometry, instead reading this information from the
     disklabel.  There are no partition tables coded into the xp
     driver, these must be placed on the drive with disklabel.

     Special files should only be created for the partitions that
     are actually used, as the overlap in these addresses could
     lead to confusion otherwise.  Traditionally the xp?a parti-
     tion is normally used for the root file system, the xp?b
     partition as a swap area, and the xp?c partition for pack-
     pack copying (it maps the entire disk).

FILES
     /dev/xp[0-7][a-h]	 block files
     /dev/rxp[0-7][a-h]  raw files
     /dev/MAKEDEV	 script to create special files
     /dev/MAKEDEV.local  script to localize special files

SEE ALSO
     hk(4), ra(4), ram(4), rk(4), rl(4), rp(4), rx(4), si(4),
     dtab(5), autoconfig(8), newfs(8)

DIAGNOSTICS
     xp%d%c: hard error sn%d cs2=%b er1=%b.  An unrecoverable
     error occurred during transfer of the specified sector of
     the specified disk partition.  The contents of the two error
     registers are also printed in octal and symbolically with
     bits decoded.  The error was either unrecoverable, or a
     large number of retry attempts (including offset positioning
     and drive recalibration) could not recover the error.

     xp%d: write locked.  The write protect switch was set on the
     drive when a write was attempted.	The write operation is
     not recoverable.

     xp%d%c: soft ecc sn%d.  A recoverable ECC error occurred on
     the specified sector of the specified disk partition.  This
     happens normally a few times a week.  If it happens more
     frequently than this the sectors where the errors are occur-
     ring should be checked to see if certain cylinders on the
     pack, spots on the carriage of the drive or heads are


Printed 11/26/99	 August 14, 1995			2


XP(4)		    UNIX Programmer's Manual		    XP(4)


     indicated.

     xp%d: unknown device type 0%o.  The number in the drive's
     drive type register is unknown to the xp driver.

BUGS
     In raw I/O read and write(2) truncate file offsets to 512-
     byte block boundaries, and write scribbles on the tail of
     incomplete blocks.  Thus, in programs that are likely to
     access raw devices, read, write and lseek(2) should always
     deal in 512-byte multiples.

     DEC-standard error logging should be supported.

     The kernel uses partition 'h' to access the badblock infor-
     mation.  This should have been 'c' except that almost all of
     the /etc/disktab entries (and thus existing systems) use 'h'
     for this purpose.	Unless you are very careful with diskla-
     bel|(8) (to make certain that no data partition overlaps the
     badblock area) you should probably leave BADSECT undefined
     in the kernel config file.


Printed 11/26/99	 August 14, 1995			3


 
Generated: 2016-12-26
Generated by man2html V0.25
page hit count: 1501
Valid CSS Valid XHTML 1.0 Strict